lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 1 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f ? description key features the LXMG221D-0700040-D2F is a fully enclosed compact solid-state led lighting driver module. it operates from a universal ac input supply in the range of 347v ac to 480v ac , 60hz to drive a string of leds with active power factor correction. led string voltage can range from 20v to 57v at a constant current of 700ma. control terminal leads include a dimming input brite a with a dedicated return lead. the amplitude of the output led string current will vary from 10% to 100% corr esponding to a 1v dc to 10v dc signal on the brite a input following the 0v to 10v esta e1.3-2001 analog control specification standard. the brite a terminal when pulled down below minimum dimming will turn off the leds and enter a low power consumption mode. a second control terminal lead provides a fault indicator. in the case that there is an led string short between output(+) and output(-), or string open, or a product over temperature condition the fault terminal will go low. the fault terminal includes an open collector device that can be pulled up to a maximum of 60v and will sink 8ma typical to 0.8v when a short or open fault occurs. to reduce audible noise the internal switching frequency remains above 30khz. safety features include open output circuit protection, whole string short circuit protection. the maximum allowable hot spot case temperature is 90c (above this temperature the module will be thermally self-protected). the recommended operating ambient temperature range is -30c to 70c, as long as the maximum case temperature is not exceeded. the compact enclosure is rated to ip66, meets ul8750 and ul1310 class 2. ? high voltage ac input: 347v ac to 480v ac ? high efficiency ? active power factor correction ? constant current 700ma ? dimming input provides 10% to 100% range, plus shutdown ? anode supply adjusts for string voltage between 20v and 57v ? small compact size ? suitable for damp locations (ip66) ? ul8750 & ul1310 ? ul file e337545 ? fcc class b ? long life expectancy ? rohs compliant ? full protection: ovp, scp, otp, maximum power limit ? unique fault detection and management ? applications residential and commercial led lighting fixtures such as: ? led down lights ? led street lights important: for the most current data, consult microsemi ?s website: http://www.microsemi.com patents pending product highlight photo is representative only, actual product may differ slightly order information part number input voltage output current fault output LXMG221D-0700040-D2F 347v ac to 480v ac 60hz 700ma dimmable current source 20v to 57v anode voltage yes
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 2 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f absolute maximum ratings input voltage (v in ) ............................................................................................................................. ............... 0v ac to 528v ac input po wer ................................................................................................................... ...................... 50w (int ernally limited) input frequency (v in ) ............................................................................................................................. ............. 57hz to 63hz peak output led string curr ent ............................................................................................... ..... 810ma (internally limited) peak output st ring volt age ................................................................................................... ........... 59.5v (internally limited) output power .................................................................................................................. .................... 44w (int ernally limited) input signal volt age (brite a input) ........................................................................... -0.3v to great er of 10v or output(+) output signal vo ltage (fault) ................................................................................................. ........................... -0.3v to 60v cold start temperature ............................................................................................................................... ..................... -30c hot spot case temperat ure, zero airflow ....................................................................................... .................................. 90c storage temperat ure ra nge ..................................................................................................... ......................... -40c to 85c note: exceeding these ratings coul d cause damage to the device. all voltages are with respect to ground. currents are positiv e into, negative out of specified terminal. recommended operating conditions (r.c.) this module has been designed to operate over a wide range of input and output conditions. however, best efficiency and perfor mance will be obtained if the module is operated under the condition listed in the ?r.c.? column. min. and max. columns indicate values beyo nd which the inverter, although operational, might not function optimally. parameter symbol min r.c. max units input supply voltage range v in 347 480 v ac linear brite a control input voltage range v brite a 0 10 v linear brite a control pwm frequency range (open collector) v brite_pwm 0.2 10 khz linear brite a control pwm amplitude range (totem pole) v brite_pwm 10 v output(+) v linear brite a control pwm frequency range (totem pole) v brite_pwm 0.2 25 khz led string voltage (at 700ma) 1 v led 40 1) 57 v output(-) sink current output(-) isink 700 ma maximum allowable case temperature t c 90 c cold start temperature t cold -30 c 1) operation has been verified down to 20v, but it is recommende d that low voltage performance w ith actual loading be verified by the user. 0 100 200 300 400 500 600 700 800 \ 30 \ 15 0 153045607590 led output current (ma) case temperature (c) typical temperature derating curve vbrite ? a ? = ? 10v vbrite ? a ? = ? 1v 0 100 200 300 400 500 600 700 800 240 280 320 360 400 440 480 520 led output current (ma) input supply voltage (v ac ) typical supply voltage derating curve vbrite ? a ? = ? 10v vbrite ?? a ? = ? 1v
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 3 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f electrical characteristics unless otherwise specified, the following specifications apply over the recommended operating co ndition except where otherwise noted; v in = 347v ac to 480v ac , 60hz; brite a = 8k ? to return; fault = 1k ? pull up to 10v full load condition uses an led load with 57v dc @ 700ma unless otherwise noted. case temperature range: -30c to 90oc; production tested at 25oc. parameter symbol test conditions / comment min typ max units input voltage v in line frequency 57 to 63 hz 312 528 v ac off power p in(min) brite a 0.5v, v in = 480v ac 0.5 w input ac current i 347 measured at full load and 347v ac input 175 ma i 480 measured at full load and 480v ac input 125 ma maximum inrush current i inrush measure at 480v ac peak ac line; maximum duration 10 s 60 a measure at 480v ac peak ac line measured after 10 s 5 a power factor full load, 347v ac to 480v ac 0.9 pf efficiency full load, v led = 57v, v in = 480v ac 88 91 % total harmonic distortion thd full load, 347v ac to 480v ac 15 % outputs average sink current i out- t a = 25c 665 700 735 ma led string voltage v out rated led current 20 57 v ripple (pk-pk) v out full load, v led = 57v, (pk to pk)/average 2 % line regulation i out- v in = nominal 10% (i.e. 480v ac 10%) 1 % load regulation iout- output(+) 40v to 57v 1 % turn-on time t turn_on cold start, power on 0.2 0.5 sec output overshoot / undershoot i out+ turning power on or off 10 % dimming brite a voltage setting v brite a for maximum brightness 9.5 10 10.5 v for minimum brightness 0.95 1 1.05 brite a output current i brite a brite a to return 1.19 1.25 1.37 ma minimum output current i min brite a = 0.95v 10 % of max output current dim range (analog dimming) i led = 700ma, brite a = 0.95v versus brite a 10v 10:1 ratio shutdown voltage v brite a 0.8 v fault output voltage low v fault short output(+) to out(-), fault = 8ma 0.8 v leakage current i fault no fault, v fault = 57v 10 a protection overvoltage protection v ov maximum out(+) 57.5 58.5 59.5 v over temperature shutdown t ot over case temperature protection hot spot 90 95 c
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 4 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f safety & emc compliance ul compliance to ul8750 & ul1310 class 2 file e337545 fcc title 47, part 15 conducted and radiated emission, class b en 61000-3-3 voltage fluctuations and flicker en61000-4-2 electrostatic discharge immunity en61000-4-3 radiated susceptibility test en61000-4-4 electrical fast transient en61000-4-5 and ansi c61.42.2 surge immunity test, ac power line, category c low exposure (6kv/3kv) en61000-4-6 conducted susceptibility immunity test en61000-4-8 power frequency magnetic field immunity test en61000-4-11 voltage dips and interruption immunity life expectancy 5 years / 50,000 hours @ 100% duty at maximum case temperature 55c mtbf 221,569 hours, case temperature 55; 12 1,565 hours case temperature 70c bellcore tr-nwt-332, issue 6; me thod 1, case 3, ground benign environmental standards eu rohs, reach lead description name pin # description input terminal leads (18awg) black ac line main input power supply line 347v ac to 480v ac white ac neutral main input power supply neutral control terminal leads (22awg) purple brite a analog dimming i nput (full brightness if open) gray return return brown fault fault signal (low during whole led string short or open) output terminal leads (18awg) red output(+) led string anode voltage (high side) blue output(-) output (-) led cath ode voltage (low side) 700ma fault table condition output(-) fault driver status comment output(+) string output (-) (700ma) on hi-z on output(+) open out(-) open low output(+) max voltage output(+) short out(-) open low shutdown output(+) string output (-) w/ 1 or more led short on hi-z on staylit? , output(+) 20v over temperature at the case hot spot open low shutdown when the temperature goes down, the module turns on again (no user intervention) power loss (blackout) event open low shutdown when power comes back, the module turns on again (no user intervention) brite a shorted to return or output(-) open hi-z shutdown brite a open (or resistor > 12kohm) on hi-z on
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 5 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f conditions of acceptability the components have been judged on the basis of the required spacings in the standard for class 2 power units, ul 1310. the input and output leads are 18 awg, rated 600v, 105oc, vw-1. the suitability of the leads shall be determined in each end- use application. the leads are suitable for factory wiring on ly, and additional investigation will be required for field wirin g. the polymeric housing is rated v-0 and has been subjected to a ball-impact test. the need for a suitable enclosure shall be considered in the end product. the component has been evaluated for dry and damp locatio ns, where the humidity conditioni ng and dielectric tests were conducted per ul 8750. the maximum temperature measured on housing outside surface was 61.3 c during the temperature test when shifted to ambient temperature 40 c. the necessity of repeated temperature test shall be determined in each end use application. a proper mechanical, electrical and fire enclosure shall be provided in the end-use application that is in compliance with all the applicable requirements of the end-use application. testing was on a 20 a branch circuit. if used on a branch circuit greater than this, additional testing may be necessary. the led driver is rated as noted in the el ectrical ratings table above, and the output s comply with the requirements for class 2. the need for additional evaluation shall be considered in the end product if used beyond these ratings. the led driver is provided with dimmer leads for connecting an external 0-10 v dc source for dimming the output current. the leads colors are shown in box below. the dimme r circuit is considered as class 2 circuit. lead function color ac line black ac neutral white output(+) red output(-) blue return gray fault brown brite a purple
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 6 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f typical characteristic charts 25c 0 10 20 30 40 50 60 0 100 200 300 400 500 600 700 012345678910 output ? voltage ? (v) output ? current ? (ma) brite_a ? input ? (v) brite ? a ? input ? vs ? output ? current ? and ? output ? voltage ? @ ? vin ? = ? 480v ac iout ? brite ? a ?? rising iout ? brite ? a ? falling output ? voltage 0.6 0.7 0.8 0.9 1 0 5 10 15 20 25 30 35 40 power ? factor output ? power ? (watts) power ? factor ? vs ? output ? power pf ? @ ? 480vac pf ? @ ? 347vac 60 70 80 90 100 0 5 10 15 20 25 30 35 40 efficiency ? (%) output ? power ? (watts) efficiency ? vs ? output ? power ? efficiency ? @ ? 480vac efficiency ? @ ? 347vac
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 7 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f mechanical drawing wire length is 230mm 10mm, strippe d 12mm 5mm ul1015 awg#18 16/30 stranded 105 c input & output wires; awg#22 7/30 stranded control wires, all wires tinned. please insure the wire nuts are installed correctly to prevent intermittent operati on. connecting the ac input to control or output wires will result in damage to the module. application information
lxmg2203 p roduction d atasheet LXMG221D-0700040-D2F microsemi analog mixed signal group 11861 western avenue, garden grove, ca. 92841, 800-877-6458, 714-898-8121, fax: 714-893-2570 page 8 copyright ? 2011 rev. 1.1, 2011-12-02 40w 700ma dimmable hv led driver module tm ? www. microsemi . com l l x x m m g g 2 2 2 2 1 1 d d - - 0 0 7 7 0 0 0 0 0 0 4 4 0 0 - - d d 2 2 f f notes production data ? information contained in this document is proprietary to microsemi and is current as of publication date. this document may not be modified in any way without the express written consent of microsemi. product processing does not necessarily include testing of all parameters. microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time.
|
